A vessel blackout investigation determines why electrical power was lost, how the failure moved through the ship’s systems, whether propulsion or steering became unavailable, how the crew and automated systems responded, and which technical or operational factors ultimately contributed to the casualty.
A blackout should not automatically be described as a generator failure. The generator may still be running while a circuit breaker, switchboard connection, transformer, control circuit, Power Management System, or downstream electrical fault interrupts power to essential equipment. The NTSB investigation of the containership Dali demonstrated this distinction: the initiating event was a loose signal wire connection that caused a high-voltage breaker to open, producing a low-voltage blackout and ultimately contributing to the loss of propulsion and steering.
A technically sound ship blackout investigation therefore follows the failure through the entire electrical and mechanical system rather than stopping at the first component that appears to have failed.
What Is a Vessel Blackout?
In marine engineering, a blackout generally refers to a loss of electrical power that prevents normal shipboard systems from operating as intended.
Not every blackout is identical.
A vessel may experience a loss of one electrical bus while another remains energized. It may lose low voltage distribution while the high voltage bus and generators remain online. It may lose the entire main electrical supply. In a more severe condition, propulsion machinery and auxiliaries may become unavailable because power is absent.
IMO terminology distinguishes the main source of electrical power, main switchboard, emergency source of electrical power, emergency switchboard, and dead ship condition. A dead ship condition exists when the main propulsion plant, boilers, and auxiliaries are not operating because power is absent.
This distinction matters during an investigation because saying “the ship lost power” does not explain which part of the power system was lost, which loads were affected, or which systems remained available.
Why Vessel Blackouts Can Lead to Collisions, Allisions, and Groundings
Electrical power supports much more than lighting.
Depending on the vessel design, electrical distribution can support steering gear pumps, cooling water pumps, fuel pumps, control systems, navigation equipment, communications, alarms, automation, engine auxiliaries, and other essential systems.
A failure can therefore develop through a dependency chain such as:
Electrical power → cooling water pump → main engine availability → propulsion
A separate chain might be:
Electrical power → steering gear pump → rudder response → directional control
The Dali casualty illustrates this relationship. Loss of low voltage power stopped machinery including main engine cooling water pumps and steering gear pumps. The main engine subsequently shut down, leaving the vessel without propulsion while steering capability was also affected.
That is why a marine blackout investigation needs both electrical and marine engineering analysis.

What Do Investigators Examine After a Vessel Blackout?
An investigator typically starts by defining the vessel’s electrical configuration before trying to explain the failure.
The questions include:
What generators were online?
Which electrical buses were energized?
Which transformer was supplying the low voltage system?
Which breakers were open or closed?
Was the Power Management System operating automatically?
Which standby generators were available?
What loads were connected?
Which emergency systems started?
Which alarms appeared first?
What changed immediately before the blackout?
From there, the investigation moves through the electrical generation, distribution, protection, automation, propulsion, steering, and recovery systems.
Generators and Electrical Sources
A vessel may use several diesel generators or generator sets to supply electrical power.
Investigators may examine:
Generator status
Voltage
Frequency
Electrical load
Fuel supply
Generator synchronization
Load sharing
Standby generator availability
Automatic generator start
Generator trip history
Engine alarms
A blackout does not necessarily mean that the diesel generator engine stopped first.
During the initial underway Dali blackout, diesel generators 3 and 4 continued running and remained connected to the high-voltage bus even though the low-voltage system had blacked out.
That distinction is important because the investigation must determine whether the source of electrical generation failed or whether electrical power was interrupted somewhere farther downstream.
Main Switchboard, Bus Bars, and Electrical Distribution
The main switchboard is central to a blackout investigation because it distributes electrical power to shipboard services.
Investigators may examine:
Main switchboard
Emergency switchboard
High voltage bus
Low voltage bus
Bus ties
Transformers
Step-down transformers
Switchboard feeders
Distribution circuits
Terminal blocks
Control wiring
Connection integrity
Single line diagrams
IMO defines the main switchboard as the switchboard directly supplied by the main source of electrical power and used to distribute electrical energy to ship services. The emergency switchboard serves emergency loads when the normal supply fails.
A very small defect in this system can have large consequences.
In the Dali investigation, improperly installed wire label banding prevented a signal wire ferrule from being fully inserted into a terminal block. The resulting inadequate connection allowed the circuit to open and caused a high-voltage breaker to open unexpectedly.
Why Circuit Breakers and Protection Systems Matter
Circuit breakers do more than turn power on and off.
They also protect the electrical distribution system when abnormal electrical conditions occur.
Investigators may review:
Circuit breaker status
Breaker trip history
Undervoltage protection
Protective relays
Control voltage
Overcurrent protection
Ground faults
Short circuits
Breaker operating mode
Protection coordination
Automatic and manual settings
One important component in the Dali investigation was the undervoltage release control circuit associated with the HR1 breaker. Investigators found that loss of the relevant signal could cause the breaker to open and interrupt low-voltage power.
This is why a vessel electrical failure investigation should not stop after discovering that a breaker opened.
The next question is:
Why did it open?
The Role of the Power Management System
The Power Management System, commonly called PMS, coordinates electrical generation and demand aboard many modern vessels.
Typical functions can include:
Generator start and stop
Load sharing
Generator synchronization
Load shedding
Standby generator management
Heavy consumer blocking
Blackout detection
Blackout restart
Power restoration sequencing
A PMS can automatically remove lower priority loads when electrical demand threatens to exceed available generation. It can also start additional generators or reconnect essential consumers during recovery. Marine power management systems commonly perform these functions to reduce blackout risk and restore electrical service after a failure.
During a vessel blackout investigation, experts should examine both the hardware and the automation logic.
A system may have adequate generator capacity but still experience a blackout if load shedding does not occur quickly enough, a standby generator fails to start, a breaker does not transfer automatically, or the system configuration prevents expected recovery.

How Investigators Reconstruct the Blackout Sequence
The central task is to build a reliable failure sequence.
A useful forensic model is:
Initiating fault → protection response → distribution loss → auxiliary systems affected → propulsion or steering affected → recovery attempt → secondary failure → casualty
This structure prevents the investigation from confusing the first failure with everything that happened afterward.
Alarm and Event Logs
Alarm history can establish the order in which systems began to fail.
Investigators may compare:
Machinery alarms
Breaker event logs
PMS records
Generator alarms
Main engine alarms
Electrical event logs
Automation system records
Alarm acknowledgement
Recovery alarms
The exact order can reveal whether the electrical problem occurred before the machinery problem or whether machinery failure caused the electrical event.
VDR and Bridge Audio
Voyage Data Recorder information can help establish vessel movement and bridge activity during the blackout.
Relevant evidence may include:
Vessel position
Speed
Heading
Bridge audio
VHF communications
Navigation information
Alarm information
Engine related data
The Dali casualty also illustrates an important limitation: during the electrical failure, some VDR system feeds were interrupted while bridge audio continued recording.
That means missing VDR parameters should not automatically be interpreted as evidence that an event did not occur.
Engine Room Records and Crew Interviews
The engine room timeline may be just as important as the bridge timeline.
Investigators may review:
Engine room logs
Chief Engineer statements
Electrical officer statements
Machinery alarm history
Generator logs
Maintenance records
Control room communications
Blackout recovery actions
Crew interviews can help explain what personnel saw and attempted, but investigators should compare those recollections with electronic and physical evidence.
The Initiating Failure and the Recovery Failure May Be Different
This is one of the most important principles in blackout root cause analysis.
The component that starts the blackout may not be the reason the ship fails to recover.
The Dali casualty provides an unusually clear example.
The first underway blackout began when the loose electrical connection led to a breaker opening and loss of low voltage power. After power was restored, a different problem developed. A flushing pump being used to supply fuel to the online diesel generators did not restart automatically after the loss of power. Fuel pressure then fell, contributing to the second blackout.
The investigation therefore had to separate:
Initiating electrical fault
from
Recovery system weakness
from
Secondary blackout
This type of separation is essential when establishing probable cause and contributing factors.
How Electrical Power Loss Can Affect Propulsion
Electrical failure can affect propulsion in several ways.
On some vessels, propulsion itself is electrically driven.
On others, the main engine is mechanically connected to the propeller, but it still depends on electrically powered auxiliary systems.
Those systems may include:
Cooling water pumps
Lubricating oil pumps
Fuel pumps
Control systems
Ventilation
Hydraulic systems
Instrumentation
Engine control equipment
A useful forensic question is:
Did the blackout directly remove propulsion power, or did it shut down an auxiliary system that caused the propulsion plant to stop?
On the Dali, loss of power to the main engine cooling water pump caused low cooling water pressure, and the main engine then shut down.
That is different from saying simply that “the blackout turned off the engine.”
The failure mechanism matters.
How a Vessel Blackout Can Cause Loss of Steering
Electrical faults may also appear operationally as steering casualties.
Steering gear commonly depends on electrically driven pumps or motors.
Investigators may inspect:
Steering gear pumps
Steering motors
Electrical feeders
Hydraulic systems
Rudder control
Emergency steering
Power supply
Breaker status
Control circuits
The NTSB investigation of the towing vessel Marquette Warrior found that an improperly positioned wiring harness inside an electrical generator contacted terminal posts and eventually caused loss of three phase electrical power to steering pump motors. The vessel then lost steering and grounded.
This case demonstrates why investigators should trace a steering failure back through the electrical system rather than treating it as an isolated hydraulic or helm problem.
What Role Does the Emergency Generator Play?
The emergency generator provides power to designated emergency services after failure of the main electrical supply.
It should not automatically be described as a complete backup for the vessel’s normal electrical plant.
IMO requirements distinguish the emergency source of electrical power from the main source and require it to support specified emergency services.
This creates an important distinction:
Restoring emergency power is not the same as restoring propulsion.
On the Dali, the emergency generator could supply selected emergency equipment, including a steering pump, but it did not provide power to restore main propulsion.
That is why investigators must identify exactly which loads the emergency switchboard can support.

Why Some Vessels Experience a Second Blackout During Recovery
Recovery is not simply a matter of switching power back on.
Generators, pumps, automation, and electrical loads must return in an appropriate sequence.
A second blackout may occur when:
A required pump does not restart
Too many loads reconnect at once
A standby generator fails
Fuel supply is interrupted
A breaker remains in the wrong operating mode
A Power Management System does not react as expected
A common cause fault remains present
The Dali case showed how a pump that lacked automatic restart and redundancy contributed to a second blackout after the initial power loss.
This illustrates a critical investigative principle:
The failure that starts the casualty and the failure that prevents successful recovery may be completely different.
How Investigators Determine the Root Cause
A professional investigation should move beyond identifying the component that failed.
It should ask why the component failed, why safeguards did not prevent escalation, and why recovery systems did or did not work.
Physical Inspection
Investigators may inspect:
Switchboards
Terminal blocks
Wiring
Circuit breakers
Generators
Transformers
Electrical panels
Steering equipment
Fuel pumps
Cooling pumps
Damaged components
Connection integrity
Physical evidence can reveal looseness, heat damage, arcing, incorrect installation, wear, contamination, vibration damage, or other conditions.
In the Dali investigation, investigators removed relevant terminal block and wiring components and examined the electrical system at the component level.
Electrical Testing
Testing may include:
Continuity testing
Insulation resistance testing
Voltage measurements
Breaker testing
Relay testing
Component testing
Electrical load testing
Event log analysis
Fault simulation
System replication
Testing should be selected according to the suspected failure mechanism rather than performed simply to generate data.
Failure Replication
One of the strongest ways to evaluate a theory is to determine whether the suspected defect can reproduce the recorded event.
During the Dali investigation, investigators recreated the relevant electrical configuration and removed the suspect wire from its terminal block. The HR1 and LR1 breakers opened and produced the same type of low-voltage blackout observed during the casualty.
That provides much stronger evidence than simply observing a loose connection after the accident.
The forensic question becomes:
Can the suspected mechanism produce the same system response recorded during the casualty?
Previous Blackouts Can Be Critical Evidence
Earlier failures can reveal that a casualty was not an isolated event.
Investigators should ask:
Did the vessel experience earlier blackouts?
Were they investigated?
Were repairs made?
Was the root cause identified?
Were relevant alarms reviewed?
Were the events reported to management?
Did operating procedures change?
Were affected systems returned to service without understanding the failure?
The Dali had experienced two blackouts while in port the day before the bridge casualty. Those events became relevant when investigators examined generator fuel supply, recovery arrangements, and the later underway blackouts.
Prior events should therefore be treated as evidence, not background trivia.
Why Maintenance Records Matter
A blackout may result from wear, installation errors, deferred maintenance, incorrect repairs, or unintended consequences of previous work.
Investigators may review:
Planned maintenance records
Generator maintenance
Switchboard maintenance
Breaker inspections
Wiring repairs
Component replacement
Previous defects
Class survey records
Manufacturer recommendations
Service reports
Post-maintenance testing
The Marquette Warrior investigation illustrates how maintenance activity itself can introduce a latent defect. The NTSB determined that a wiring harness had likely been positioned incorrectly during maintenance before it later contacted generator terminal posts and contributed to loss of steering power.
Can Infrared Thermal Imaging Help Identify Electrical Faults?
Infrared thermal imaging can help identify abnormal temperature patterns in energized electrical systems.
Potential findings may include:
High resistance connections
Loose connections
Overheated terminals
Unbalanced loads
Abnormally warm breakers
Localized switchboard heating
Thermography cannot detect every electrical defect, and a normal thermal image does not guarantee that an electrical system is free from problems.
However, it can reveal conditions that may not be obvious during an ordinary visual inspection.
The NTSB concluded that infrared thermal imaging of the Dali high-voltage switchboard connections as part of preventive maintenance might have identified the inadequate Wire 1 connection before the casualty.
This topic is particularly relevant to A&L Maritime Experts because the company lists thermographic inspections for marine electrical, mechanical, and structural systems among its technical capabilities.
What Happens to Electronic Evidence During a Blackout?
A blackout can affect the very systems investigators later need for reconstruction.
Potential electronic evidence includes:
VDR data
PMS logs
Integrated Automation System records
Breaker event logs
Generator logs
Alarm history
Engine data
Bridge audio
Electronic control room records
Navigation information
System timestamps
Investigators should determine which systems were independently powered, which lost electrical supply, and whether data gaps correspond with the blackout itself.
The Dali investigation showed that bridge audio continued even when some VDR system feeds were interrupted.
This makes data preservation and cross-checking especially important.
What Evidence Should Be Preserved After a Vessel Blackout?
For attorneys, insurers, operators, and vessel owners, early evidence preservation can make a significant difference.
Important evidence may include:
| Evidence | What It May Help Establish |
|---|---|
| Breaker event logs | Which breaker opened and when |
| PMS records | Generator and load management response |
| Alarm history | Sequence of warnings before and after the failure |
| VDR data | Vessel movement and bridge timeline |
| Bridge audio | Commands, warnings, and communications |
| Generator logs | Generator status, load, and shutdown sequence |
| Engine logs | Main engine shutdown and restart attempts |
| Electrical single line diagrams | How the failure could move through the distribution system |
| Switchboard inspection | Condition of terminals, breakers, and wiring |
| Maintenance records | Earlier defects, repairs, and inspection history |
| Previous blackout records | Whether warning events occurred before the casualty |
| Thermal imaging | Abnormal heat that may indicate resistance or poor connections |
| Component testing | Whether a suspected failure mechanism can be reproduced |
| Crew statements | What personnel observed and attempted |
| Manufacturer information | Expected component and system behavior |
| Physical damage | Consequences of the power loss and resulting casualty |
Failed components should be preserved where practical, and investigators should document when and how data or components were collected.
How Human Factors and Blackout Procedures Are Evaluated
A blackout is not purely an electrical event.
Crew actions influence whether the ship recovers successfully.
Investigators may consider:
Alarm recognition
Chief Engineer response
Electrical officer actions
Engine room troubleshooting
Bridge and engine room communication
Blackout recovery procedures
Crew training
Emergency drills
Decision making
Automation awareness
Human machine interaction
Safety Management System procedures
A technically correct system can still produce a serious casualty if personnel cannot identify the failure quickly enough or do not understand how the automatic systems are configured.
Likewise, a strong crew may have too little time to recover if the vessel is already close to a bridge, shoal, dock, or other hazard.
The NTSB has emphasized in other marine casualties that effective Safety Management System procedures and training for propulsion and steering loss can improve crew response when time is critical.
Root Cause Versus Contributing Factors
A professional investigation should distinguish between several levels of causation.
Initiating event
The event that begins the failure sequence.
Direct technical effect
What happened immediately because of that event.
Contributing factor
A condition that made the casualty more likely or made recovery less effective.
Recovery failure
A separate problem that prevented the vessel from returning to normal operation.
Operational consequence
The eventual loss of steering, propulsion, maneuverability, collision, allision, or grounding.
For example, saying:
“The generator failed and caused the accident”
may be technically incomplete.
A better investigation asks:
Why was power lost?
Why did the protective system react?
Why did redundancy not prevent the blackout?
What loads were lost?
Why did propulsion stop?
Was steering restored?
Why did recovery take as long as it did?
Was a second blackout caused by the same defect or a different condition?
Were prior warning signs present?
Those questions lead toward a defensible blackout root cause analysis.
How Investigators Test Alternative Explanations
Early accident reports often contain several competing theories.
Possible explanations might include:
Fuel contamination
Generator failure
Electrical short circuit
Loose connection
Breaker malfunction
Power Management System failure
Steering failure
Human error
Maintenance error
Investigators should not select a theory because it appears first or sounds plausible.
A stronger process is:
Hypothesis → evidence collection → system analysis → physical testing → comparison with recorded events → confirmation or rejection
In the Dali investigation, component inspection and electrical replication helped establish the failure mechanism tied to the loose signal wire, rather than relying on early speculation.
What Does a Vessel Blackout Investigation Report Include?
A useful technical report should explain both the evidence and the reasoning.
It may include:
Incident background
Vessel electrical configuration
Generator status
Switchboard arrangement
Electrical single line diagram
Breaker status
Power Management System operation
Alarm chronology
VDR and bridge audio review
Engine room timeline
Propulsion effects
Steering effects
Emergency generator response
Previous blackout history
Maintenance review
Physical inspection findings
Electrical test results
Component examination
Failure replication
Human factors
Safety Management System review
Alternative theories considered
Initiating cause
Contributing factors
Recovery failures
Technical conclusions
Limitations
The report should make clear what investigators directly observed, what electronic records established, and which conclusions require technical interpretation.
The U.S. Coast Guard similarly publishes marine casualty investigations containing findings of fact, analysis, conclusions, and recommendations.
When Is a Marine Expert Needed After a Vessel Blackout?
Independent technical analysis can be especially useful when:
The cause of the blackout is disputed
The vessel suffered collision, allision, or grounding
Propulsion or steering failure is questioned
An insurer disputes the failure mechanism
Multiple electrical failures occurred
Previous blackouts were recorded
Maintenance work may have contributed
Electronic records conflict with crew statements
A component requires laboratory examination
A litigation matter requires technical explanation
A&L Maritime Experts provides marine accident investigation, forensic engineering analysis, accident reconstruction, thermographic inspection, and expert support for technical maritime matters. Its existing Accident Investigation page covers propulsion failures and system malfunctions, while its broader technical capabilities include infrared thermography and forensic root cause analysis.
Readers who need a broader reconstruction of the casualty can review A&L’s Accident Reconstruction service. Where the findings become part of a disputed claim or litigation matter, the Marine Legal Experts page provides the more relevant next step.
Frequently Asked Questions
What causes a vessel blackout?
A vessel blackout can result from generator problems, breaker trips, faulty electrical connections, switchboard faults, transformer problems, protection system operation, fuel supply problems, automation issues, distribution failures, or combinations of several conditions. Investigators must establish the actual failure sequence rather than assume the generator itself failed first.
Can a ship lose electrical power while its generators are still running?
Yes. Electrical generation can remain available while a breaker, transformer, bus, or downstream distribution failure prevents power from reaching shipboard loads. During the initial Dali underway blackout, generators remained running on the high-voltage bus while the low-voltage system lost power.
Does the emergency generator restore ship propulsion?
Not necessarily. Emergency generators are designed to supply designated emergency services rather than automatically restore the entire normal electrical plant. On the Dali, emergency generation supported certain emergency loads but could not restore main propulsion.
How do investigators find the root cause of a ship blackout?
Investigators reconstruct the electrical configuration and timeline, review alarm and event logs, inspect switchboards and generators, examine maintenance records, analyze VDR and engine room information, test suspected components, and compare alternative failure theories. In some cases, investigators may reproduce the suspected fault to determine whether it creates the same blackout sequence.
Can thermal imaging help prevent marine electrical blackouts?
Thermal imaging can reveal abnormal heating associated with loose or high-resistance electrical connections, overloaded components, and other defects. It does not detect every possible problem, but the NTSB found that preventive infrared imaging could potentially have identified the inadequate electrical connection involved in the Dali casualty.
Follow the Failure, Not the Assumption
A strong vessel blackout investigation should explain more than which piece of equipment stopped working.
The investigator must trace the complete causal chain from the initiating electrical fault through breaker and protection behavior, electrical distribution, critical auxiliaries, propulsion and steering response, emergency power, recovery attempts, secondary failures, maintenance history, and human actions.
That approach can reveal why a seemingly small electrical defect became a serious marine casualty and whether the systems intended to prevent or contain the failure worked as designed.
A&L Maritime Experts combines marine engineering knowledge, vessel inspections, accident reconstruction, forensic analysis, infrared thermal imaging, and litigation support to evaluate complex system failures. If a blackout, electrical failure, propulsion loss, steering casualty, collision, allision, or grounding requires independent technical review, contact A&L Maritime Experts to discuss the available evidence and investigation scope.

